Hyundai Veloster Manuals

Hyundai Veloster: Antenna. Repair procedures - AVN System - Body Electrical SystemHyundai Veloster: Antenna. Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Body Electrical System / AVN System / Antenna. Repair procedures

Inspection

Glass Antenna Test
1.
Wrap aluminum foil (A) around the tip of the tester probe (B) as shown.
2.
Touch one tester probe to the glass antenna terminal (A) and move the other tester probe along the antenna wires to check that continuity exists.
Glass Antenna Repair
To make an effective repair, the broken section must be no longer than one inch.
1.
Lightly rub the area around the broken section (A) with fine steel wool, and then clean it with alcohol.
2.
Carefully mask above and below the broken portion of the glass antenna wire (B) with cellophane tape (C).
3.
Using a small brush, apply a heavy coat of silver conductive paint (A) extending about 1/8″on both sides of the break. Allow 30 minutes to dry.
Thoroughly mix the paint before use.

4.
Check for continuity in the repaired wire.
5.
Apply a second coat of paint in the same way. Let it dry three hours before removing the tape.
Glass Antenna Circuit Inspection
1.
Remove the right side rear quarter trim.
Then disconnect the antenna feeder cable (A) from the glass antenna amp.
2.
Turn the radio ON.
Measure the voltage between the harness side feeder cable (A) and body ground (B).
OK : approximately 12V (ACC+)

3.
Check for FM wire resistance between terminals of No.1 and 3
1. FM antenna grid terminal
2. AM antenna grid terminal
3. Body ground.

Standard value : 80~120KΩ
Short : Approx. 0Ω
Open : ∞ Ω
4.
Check for AM wire resistance between terminals of No.2 and 3.
Standard value : 120~170KΩ
Short : Approx. 0Ω
Open : ∞ Ω
5.
Check the grid lines for continuity.
6.
When a poor radio reception is not repaired through the above inspection methods, replace the amp.
If the radio reception is still poor, check the radio cable for short and radio head unit for failure.
Antenna Cable
1.
Remove the antenna jack (A) from the AVN unit and antenna.
2.
Check for continuity between the center poles of antenna cable.
3.
Check for continuity between the outer poles of antenna cable. There should be continuity.
4.
If there is no continuity, replace the antenna cable.
5.
Check for continuity between the center pole (A) and window antenna pole (B). There should be continuity.
6.
If there is not continuity, replace the external amplifier.
7.
Check for continuity between the center pole (A) and outer pole (B) of antenna cable. There should be no continuity.
8.
If there is continuity, replace the antenna cable.

Speakers. Repair procedures
Inspection 1. Troubleshooting for Speaker (1) Basic inspection of speaker Inspect the sound from speaker after verifying that ...

GPS Antenna. Repair procedures
Removal Roof Antenna (GPS) 1. Remove the rear roof trim. (Refer to the BD group - "Roof trim") 2. Disconnect the cables ( ...

See also:

Anchor Pretensioner (APT). Description and Operation
Description Front anchor pretensioner operates as well as Belt Pretensioner at the same time If it gets into its deploy condition after a collision. It is located at near anchor on driver se ...

Tire care
For proper maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your ...

Disarmed stage
Using the smart key (if equipped) The system will be disarmed when the doors are unlocked by pressing the unlock button on the smart key or pressing the lock/unlock button of the front outside do ...

Categories


В© 2011-2024 Copyright www.hvmanual.com